Recent Posts

Pages: [1] 2 3 ... 10
1
GENERAL DISCUSSION TO INCLUDE OFF TOPIC / Re: If you love dogs..
« Last post by PJB on Today at 07:34:28 AM »



Sent from my iPhone using Tapatalk
2
GENERAL DISCUSSION TO INCLUDE OFF TOPIC / Re: What Did You Do Today
« Last post by Carpenter84 on September 18, 2021, 10:13:12 PM »
Ah ok. cool.

unrelated - maaan they have that linear slide just a craaaankin! Can't imagine the screws pushing that table back and forth will last long at that speed.
3
GENERAL DISCUSSION TO INCLUDE OFF TOPIC / Re: What Did You Do Today
« Last post by PJB on September 18, 2021, 10:02:22 PM »
Screen printing machine.   
I make the tools to fit the glasswork they send me.
Grippers, nose cones etc.

https://youtu.be/zjneTuCYNcY


Sent from my iPhone using Tapatalk
4
GENERAL DISCUSSION TO INCLUDE OFF TOPIC / Re: What did you buy today?
« Last post by Carpenter84 on September 18, 2021, 09:55:04 PM »
No, mine are both R8. If the BT40 tapping heads were auto reversing I would have bought the lot and either cut off the taper or turned it to an R8. But since both my mills have quills, I don't need the tapping heads that's only slide up and down and not auto reverse.
Sure, I could have grabbed the lot for the $200 he was asking since the happing heads alone are probably a few hundred, I didn't bother because he's had them listed for sale for a while now. Wasn't worth it in my opinion.
5
GENERAL DISCUSSION TO INCLUDE OFF TOPIC / Re: If you love dogs..
« Last post by 34_40 on September 18, 2021, 07:09:36 PM »
Congrats Shawn!  He's a cutie..  :bravo_2:
6
GENERAL DISCUSSION TO INCLUDE OFF TOPIC / Re: If you love dogs..
« Last post by 4GSR on September 18, 2021, 07:01:32 PM »
I see he found something to chew on.

Better get you a dump truck load of dirt.  You will need it to fill all those holes he's going to dig!!! :)

Congratulations!
7
GENERAL DISCUSSION TO INCLUDE OFF TOPIC / Re: What did you buy today?
« Last post by RayH on September 18, 2021, 06:40:27 PM »
Shawn,

You mentioned BT 40 T/C tapping adaptors. Is your Induma spindle BT40?
8
GENERAL DISCUSSION TO INCLUDE OFF TOPIC / Re: What did you buy today?
« Last post by Carpenter84 on September 18, 2021, 05:51:31 PM »
Grabbed this 10x14 angle table locally this week. I haven't spent any cash on local stuff in a while. I get weird with spending cash, not sure why. Always feels like there's never enough when it's in my wallet...
Anyways, I felt it was a good deal at $250. Met a cool dude who does machining and fabrication. He had some BT 40 taper tool holders with tapping heads, but there were just the in and out cushion style tapping heads, not the auto reversing. Otherwise I would have been all over them.
I do not have a use for this currently, but I sure have needed one several times, even recently. So, happy to have it.
It's chinese I believe, needs a to be ground or scraped, and the heavy machining tool marks in the radius ways could be smoothed out, but it's cool.
Has pin holes for common angles.

9
GENERAL DISCUSSION TO INCLUDE OFF TOPIC / Re: What Did You Do Today
« Last post by Carpenter84 on September 18, 2021, 04:52:54 PM »
What is the nylon part for? Some kind of stand or riser?
10
GENERAL DISCUSSION TO INCLUDE OFF TOPIC / Re: What Did You Do Today
« Last post by PJB on September 18, 2021, 04:44:36 PM »
Small tooling job for a perfume bottle came today. 
Nylon eezy stuff.   
These are where I use the waterjet cut radius bits to shape the bottom contours





Sent from my iPhone using Tapatalk
Pages: [1] 2 3 ... 10